Get the upgrades you want with 4-month interest-free financing

DPF regeneration explained

Most diesel owners only hear the word regeneration when something has gone wrong with the exhaust filter. Knowing how DPF regeneration works, and what gets in its way, is the easiest way to avoid warning lights, limp mode and a filter that needs cleaning.

This explainer covers the three types of regeneration and what you can do to help each one along.

Smoke from a car's twin exhaust pipes

Why a DPF needs to regenerate

A diesel particulate filter catches the soot a diesel engine produces, so it doesn't leave the tailpipe as black smoke. That soot has to go somewhere, and a filter that only ever collected it would block in no time.

Regeneration is the car's way of emptying it, by heating the filter enough to burn the trapped soot off. When it works as intended, the AA says a DPF on a car that's used correctly should last well over 100,000 miles.

Passive regeneration

Passive regeneration happens on its own whenever the exhaust runs hot enough for long enough. That usually means sustained speed on a motorway or fast A-road, and the RAC suggests a good 30 to 50 minute run of that kind every so often.

You won't notice it happening and there's nothing to switch on. Cars that do regular longer journeys get most of their soot cleared this way, which is why their filters rarely cause trouble.

Exhaust smoke from the back of a silver car
Twin exhaust tailpipes seen from under the back of a car

Active regeneration

When the filter fills to a set level and passive regeneration hasn't kept up, the engine software steps in. It adds extra fuel to raise the exhaust temperature and burn the soot off while you're on the move. The AA puts this at roughly every 300 miles, taking 5 to 10 minutes, though the exact pattern varies between makes. You may notice some of these signs while it's running.

  • The cooling fans keep going, sometimes after you've parked.
  • Idle speed sits a little higher than normal.
  • Stop/start no longer cuts the engine at junctions.
  • Fuel use rises slightly.
  • A hot, acrid smell comes from the exhaust.
  • The engine note changes.

If the journey ends before it finishes, the job is left half done and the soot keeps building. When you spot these signs, carrying on at a steady speed for another 10 minutes or so gives it the chance to complete.

Forced regeneration

Once the soot level climbs past what active regeneration can handle, the car may restrict performance and a run on the motorway will no longer clear it. At that point a garage can connect diagnostic equipment and command the engine to run a regeneration while the vehicle is stationary.

This is known as a forced or manual regeneration. If the filter is too badly blocked even for that, it needs cleaning, and a replacement is the last resort for a filter that's damaged.

Technician reading fault codes on a diagnostic tablet plugged into the car

The three types side by side

Passive Active Forced
What starts it Exhaust heat from sustained speed The engine software, once the filter reaches a set soot level A technician using diagnostic equipment
Where it happens On the road On the road With the vehicle stationary
What you need to do Make a regular longer run at a steady speed Let it finish once it has started Book it in once the light won't clear
Signs it's happening None you'd notice Fans running, higher idle, stop/start off, hot smell Done by the technician

What stops a DPF regenerating

Most regeneration problems come down to how the car is used and looked after. These are the common culprits.

Instrument cluster with the engine and oil warning lights on

Short journeys at low speed

The exhaust never gets hot enough, and active regens are cut off before they finish.

Running low on fuel

The AA notes that a car with less than about a quarter of a tank may not start an active regeneration.

The wrong engine oil

Most DPF-equipped diesels need a low-ash oil, and the wrong specification can clog the filter early. Your handbook lists the right one.

Faults elsewhere in the engine

A sticking EGR valve, an injector problem or a faulty sensor can add soot or stop a regen from starting. Any warning light on the dash can block regeneration too.

Missed services and empty additive tanks

Overdue servicing doesn't help, and on cars that use a separate DPF fuel additive, an empty additive tank lets the filter block quickly.

If the light keeps coming back even with longer runs, a free diagnostic check will show which of these is behind it.

Why choose Essex Tuning for DPF problems

When regeneration can't keep up, we come to the car, read the codes and check the filter before recommending anything. Our technicians are IMI-qualified, and DPF cleaning with TerraClean is carried out on site. We've now cleaned, remapped or secured more than 1,000 vehicles.

Code reader plugged into a car's diagnostic port

Book a DPF check with us

A filter that regenerates properly looks after itself, and one that can't will only get worse with time. Call 01206 417417, or email sales@essextuningltd.co.uk to describe a typical week of journeys, and we'll find a time that suits you.

Phone 01206 417417
Based in Harwich, Essex
Hours Monday to Friday 9am–5:30pm